Place the Holder in the Pocket Charger and perform a RESET by pressing and holding down the Pocket Charger button for 10 seconds (until the lights fade out). The RESET is confirmed when you release the button and all Lights blink three times.
After RESETTING your device properly, does the experience only start after inserting a tobacco stick or by pressing the button on the Holder?
After RESETTING your device properly, does the experience only start after inserting a tobacco stick or by pressing the button on the Holder?
2. Press the pocket charger button for 4 seconds to turn your device ON. Remember, the same action applies to turn it OFF as well. Turning OFF the pocket charger will also turn OFF the holder.
After these steps, did the lights of your device turn ON?
•Turning ON the Pocket Charger by pressing the button for 4 seconds
•Place the Holder in the Pocket Charger
Step Two
•Make sure that the Holder lights on the Pocket Charger pulse to indicate the Holder is charging
•In case Holder is not charging c heck to see if the contacts need cleaning click here to see how)
Step Three
•Place the Holder in the Pocket Charger and perform a RESET: press and hold down the Pocket Charger button for 10 seconds (until the lights fade out). RESET will be confirmed when you release the button and all lights blink 3 times
Note: The holder will interrupt an ongoing experience if it is placed too close to a magnet or magnetic field and the Pocket Charger has magnets.
After following these steps did you manage to turn ON the Holder?
Seeing a light on a deeply discharged pocket charger may take up to 15 mins
Your Pocket Charger might be discharged
1. Ensure the optimal charge for your device;
Use official IQOS power adaptor and cable. Unofficial ones may interrupt the charging.
Refrain from charging with a laptop. This may also interrupt the charging.
2. Place the holder back inside the pocket charger. Ensure to place it correctly.
3. Plug the pocket charger into a wall power outlet.
While the pocket charger is being charged, strip lights will be pulsing.
Seeing a light on a deeply discharged pocket charger may take up to 15 minutes.
After these steps, did your pocket charger start to be charged? (Please note that, if you choose the option “NO”, this will take you to pocket charger diagnostics. In this case, please choose “no lights on pocket charger”)
In order to be able to diagnose and to replace the correct device part (if eligible), please choose your respective “POCKET CHARGER”, and proceed with pocket charger diagnosticsby choosing the suitable issue
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Do you want to proceed to eligibility check?
Click “Start” and login, select or add the correct device, and proceed with diagnostics.
Please be aware that such malfunctions may also be caused by improper handling such as dropping the device on the floor or by ingress of liquids into the device. Such cases do not qualify for our warranty program. Should that establish such events occurred with your device you may incur additional charges in relation to the replacement.
Can you confirm that the device was properly handled?
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Do you want to proceed to eligibility check?
Click “Start” and login, select or add the correct device, and proceed with diagnostics.
1. Place the holder in the Pocket Charger. Ensure to place it correctly.
2. Press and hold down the ON/OFF button on the Pocket Charger for 10 seconds until status lights fade out.
Please note: If your IQOS ILUMA is turned OFF at the time of RESET; when pressing the button, after the first 4 seconds, the device will turn ON: lights will fade in and the device will vibrate. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds.
3.RESET is confirmed when status lights fade in again and the device vibrates.
Ensure a magnet has not been placed near the end of the Holder where the stick is inserted. The holder shouldn’t be placed against the PC during an experience as the PC contains a magnet. Proximity to a magnet can affect the device calibration and activate a red light error.
A failed firmware update can cause blinking red light. Please, try updating your firmware again.
As every electronic device, IQOS is also built from two core elements – physical device items and the digital working instructions, called as firmware.
Firmware of your holder and pocket charger can be regularly updated for maintenance and improvement of your device performance.
Firmware update can be done through IQOS App or visiting an IQOS Store.
1. Place the holder in the Pocket Charger. Ensure to place it correctly.
2. Press and hold down the ON/OFF button on the Pocket Charger for 10 seconds until status lights fade out.
Please note: If your IQOS ILUMA is turned OFF at the time of RESET; when pressing the button, after the first 4 seconds, the device will turn ON: lights will fade in and the device will vibrate. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds.
3. RESET is confirmed when status lights fade in again and the device vibrates.
Visit our “Support” section to learn further tips about the maintenance of your device.
Within “Get Support” page, you can find useful tip and tricks, firmware update and more information about your device usage and maintenance. Visit get support page!
1. Place the holder back inside the pocket charger. Ensure to place it correctly.
2. Ensure the Pocket Charger is ON by short pressing the ON/OFF Button.
If you don’t see any lights on your pocket charger, press the pocket charger button for 4 seconds to turn your device ON. Remember, the same action applies to turn it OFF as well. Turning OFF the pocket charger will also turn OFF the holder.
If your pocket charger is already ON, solid white strip lights will turn on showing the charge level of your Pocket Charger.
Make sure your pocket charger is charged enough to fully charge the holder.
3. Ensure the optimal charging for your device.
Use official IQOS power adaptor and cable. Unofficial ones may interrupt the charging.
Refrain from charging with a laptop. This may also interrupt the charging.
Check and remove, if necessary, residues or dust that may interfere with the contacts between holder and pocket charger.
4. Leave the Holder to charge for about 5 min or until the first holder light on the Pocket Charger turns solid white.
After these steps, did your holder start to be charged? (Please note that, if you choose the option “NO”, this will take you to pocket charger diagnostics. In this case, please choose “pocket charger not charging the holder”)
In order to be able to diagnose and to replace the correct device part (if eligible), please choose your respective “POCKET CHARGER”, and proceed with pocket charger diagnosticsby choosing the suitable issue
Holder light is ON, but experience doesn’t start automatically
Connect to the IQOS App
The AutoStart function might have been deactivated from IQOS App
1.Make sure your device is connected to the IQOS App: Before performing connection steps, please;
Make sure both Charger and Holder are registered on your profile on iqos.com.
If you are using web app, clear your cache in the browser.
Make sure your holder is inside the pocket charger before performing a Bluetooth connection.
2.Let’s follow these few steps to connect your mobile device to the IQOS App:
a. Remove all devices, not only IQOS, from the Bluetooth settings of the respective end device.
b. Turn OFF Bluetooth on the phone/PC.
c. Turn ON back Bluetooth on the phone/PC again.
d. Turn OFF your IQOS and turn it ON again by pressing the pocket charger button for 4 seconds. This will instantly re-active Bluetooth of your IQOS device.
e. Log in to IQOS App again and follow the shown steps.
3.Ensure that only one IQOS device is connected via Bluetooth.
4.If you are using an iOS device, make sure you launch the IQOS app using the Bluefy browser.
5.If this does not work, try pairing your IQOS via USB cable on Mac or PC.
6.From the IQOS App, ensure that the AutoStart function hasn’t been de-activated: AutoStart is always activated by default on a new device.
Holder light is ON, but experience doesn’t start automatically
Ensure you are using the right TEREA stick consumable
1. IQOS ILUMA is designed to be used only with TEREA sticks: ensure you are using the right consumable; the device will not start with any other tobacco sticks.
2. Ensure the TEREA sticks are being placed in the holder in the right direction and the line just above the top of the Holder. Ensure there is no debris in the holder which needs to be removed with a wooden toothpick. Please, do not insert any metallic objects in the holder.
3. Try with another TEREA sticks properly inserted in the holder and start an experience by pressing the button for 2 seconds. If available, use a stick from a different pack.
Holder light is ON, but experience doesn’t start automatically
How to Reset
Your holder’s software might need a reset
Let's Perform a RESET:
1. Place the holder in the Pocket Charger. Ensure to place it correctly.
2. Press and hold down the ON/OFF button on the Pocket Charger for 10 seconds until status lights fade out.
Please note: If your IQOS ILUMA is turned OFF at the time of RESET; when pressing the button, after the first 4 seconds, the device will turn ON: lights will fade in and the device will vibrate. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds.
3. RESET is confirmed when status lights fade in again and the device vibrates.
Holder light is ON, but experience doesn’t start automatically
Update your firmware
Firmware may need to be updated
As every electronic device, IQOS is also built from two core elements – physical device items and the digital working instructions, called as firmware.
Firmware of your holder and pocket charger can be regularly updated for maintenance and improvement of your device performance.
Firmware update can be done through IQOS App or visiting an IQOS Store.
Holder light is ON, but experience doesn’t start automatically
Check whether the AutoStart always fails
Please, check whether your device never starts automatically or if it is sporadic occurrence
On occasion, the device may not start automatically due to a number of factors such as stick positioning and aligment, device calibration, holder low on battery charge.
Holder light is ON, but experience doesn’t start automatically
How to turn ON the device
Let’s try to start the experience manually
1.Ensure the device is turned ON:
Press the pocket charger button for 4 seconds to turn your device ON. Remember, the same action applies to turn it OFF as well. Turning OFF the pocket charger will also turn OFF the holder.
2. Take your holder and insert a TEREA stick: make sure the consumable is being placed in the holder in the right direction and the line being aligned with the top of the Holder.
3. Press the holder button for 2 seconds to start the experience manually.
Bluetooth connection issues, cosmetic damages (such as scratches, dents, broken plastic, hairline cracks, discoloration), damage or failure caused by normal wear and tear of your device are excluded from voluntary warranty and accidental damage coverage.
If you wish to reach a customer service representative, visit “contact us” page to choose the channel of your preference.
1. Before trying to remove the broken TEREA stick, make sure your holder is switched off: place the holder inside the Pocket charger and press the ON/OFF button for 4 seconds. Allow the holder to cool down properly before attempting to remove the broken stick.
To confirm that it is off, remove the holder from the pocket charger and press the holder button quickly. If no lights appear, the holder is OFF and it is safe to proceed with the extraction. If lights appear, repeat the previous step to turn off the holder.
2. A new IQOS ILUMA stick extractor tool has been developed to ensure that any broken TEREA SMARTCORE STICK™ stuck in a holder can be extracted successfully as shown in the graphic and without any risk of damage to the holder.
Please, follow the steps here below to remove the broken TEREA SMARTCORE stick ™ using the IQOS ILUMA stick extractor:
1. Make sure the holder and the stick are cooled down before proceeding.
2. Carefully insert the hook of the IQOS ILUMA Stick Extractor in the holder until the plastic top part of the tool touches the holder ring.
3. Rotate the IQOS ILUMA Stick Extractor by approximately 90 degrees and pull it out carefully to extract the piece of broken stick.
4. Once you have removed the remaining part of the stick, look inside your device to ensure that there is no debris left in the bottom of the heating chamber.
5. Once the stick has been removed successfully, turn on the holder by placing it in the pocket charger and pressing the pocket charger button for 4s until all the lights turn on and the charge level is displayed.
6. Dispose of any waste as per your local waste regulation or collect and return them to us. If you need further assistance, please, visit one of our IQOS stores.
Please note: IQOS ILUMA is designed to be used only with TEREA sticks . Do not use IQOS ILUMA with previous tobacco stick generations, as this may cause damage to your device.
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Do you want to proceed to eligibility check?
Click “Start” and login, select or add the correct device, and proceed with diagnostics.
To remove a broken TEREA stick that got stuck in your Holder, please follow the below steps:
1. Make sure the holder and the stick are cooled down before proceeding.
2. To improve the access to TEREA SMARTCORE STICK™ and help with its removal, you can remove the ring from the holder taking care not to lose it.
3. Use two fingers to carefully remove the broken TEREA SMARTCORE STICK™. If it cannot be removed using your fingers, try using a toothpick or a pair of tweezers or a metal clip to remove the part of the stick that remains in the device. Please, use extreme caution when inserting any object into the heating chamber as excessive force may damage the internal surface within.
4.Once you have removed the remaining part of TEREA SMARTCORE STICK™ check inside your holder to ensure that there is no debris left in the bottom of the heating chamber.
5. Once the stick has been removed successfully, turn on the holder by placing it in the pocket charger and pressing the pocket charger button for 4s until all the lights turn on and the charge level is displayed and re-fit the ring if previously removed.
6. Dispose of any waste as per your local waste regulation or collect and return them to us. If you need further assistance, please, visit one of our IQOS stores.
Please note: IQOS ILUMA is designed to be used only with TEREA sticks . Do not use IQOS ILUMA with previous tobacco stick generations, as this may cause damage to your device.
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Do you want to proceed to eligibility check?
Click “Start” and login, select or add the correct device, and proceed with diagnostics.
Heating starting automatically without a consumable
How to Reset
Your holder’s software might need a reset
Let's Perform a RESET:
1. Place the holder in the Pocket Charger. Ensure to place it correctly.
2. Press and hold down the ON/OFF button on the Pocket Charger for 10 seconds until status lights fade out.
Please note: If your IQOS ILUMA is turned OFF at the time of RESET; when pressing the button, after the first 4 seconds, the device will turn ON: lights will fade in and the device will vibrate. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds.
3. RESET is confirmed when status lights fade in again and the device vibrates.
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Do you want to proceed to eligibility check?
Click “Start” and login, select or add the correct device, and proceed with diagnostics.
Bluetooth connection issues, cosmetic damages (such as scratches, dents, broken plastic, hairline cracks, discoloration), damage or failure caused by normal wear and tear of your device are excluded from voluntary warranty and accidental damage coverage.
If you wish to reach a customer service representative, visit “contact us” page to choose the channel of your preference.
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Do you want to proceed to eligibility check?
Click “Start” and login, select or add the correct device, and proceed with diagnostics.
When your IQOS ILUMA is not functioning as expected, usually some generic steps help to resolve the issue. Let’s start with a RESET
Let's Perform a RESET:
1. Place the holder in the Pocket Charger. Ensure to place it correctly.
2. Press and hold down the ON/OFF button on the Pocket Charger for 10 seconds until status lights fade out.
Please note: If your IQOS ILUMA is turned OFF at the time of RESET; when pressing the button, after the first 4 seconds, the device will turn ON: lights will fade in and the device will vibrate. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds.
3. RESET is confirmed when status lights fade in again and the device vibrates.
Inhalation experience duration is less than what it is designed for
Ensure the right consumable was inserted correctly
COMMUNICATE:
The device is designed to provide you experiences that each have up to 6 mins and/or 14 puffs whichever comes first. IQOS ILUMA is designed to be used only with TEREA sticks . Do not use IQOS ILUMA with previous tobacco stick generations, as this may cause damage to your device.
The device must heat up for 20 second in order to allow for aerosol creation. Ensure that there are intervals (time) between puffs. Leaving time between puffs allows the Holder to properly heat the tobacco and generate aerosol.
CONFIRM OR TEST TOGETHER WITH THE CONSUMER:
1. Check the consumable was not accidentally used twice.
2. Ensure the Consumable was inserted correctly. There are filters on both sides, but you need to have the mouthpiece filter placed outside the device for it to function correctly.
3. Check if this is an isolated TEREA fabrication issue. If this is an isolated issue with an individual TEREA, try a new TEREA consumable.
4. Does it deliver experiences with 14 puffs OR around 6 minutes?
DECIDE:
According to the above steps and the consumer’s claim, make the decision;
Option A: Inhalation delivery duration and puffs are within acceptable limits, therefore, DO NOT replace.
Option B: Let’s check if your device is still under warranty, if so, we may have the possibility to replace your device.
Use GTPs Global ID431A to inform the consumer about the reason why the holder may be perceived as warm and why it is still safe to use it.
COMMUNICATE:
If the holder warmth is creating discomfort for the user, advise to leave the device to cool down prior to starting another experience and only use the device in an environment cooler than 40degC.
Only option A since there are no issue with the device, it's all about usage conditions and perception. Do not replace.
Cosmetic damage (such as scratches, dents, broken plastic, hairline cracks, discoloration), damage (improper handling or liquid contact) or failure caused by normal wear and tear of your device are excluded from voluntary warranty program.
Our online store offers a wide range of accessories designed for IQOS ILUMA that could help you minimize the impact of the cosmetic damage.
If you wish to speak to a Customer Care representative, please contact us at:
800MYIQOS (694767)
This product is not risk free and provides nicotine, which is addictive. Only for use by adults.
Ensure a magnet has not been placed near the end of the Holder where the stick is inserted. This can affect the calibration of the device and activate a red light error.
Step Two
Place the Holder in the Pocket Charger and perform a RESET by pressing and holding down the Pocket Charger button for 10 seconds (until the lights fade out) The RESET will be confirmed when you release the button and all lights blink three times.
When the Holder turns ON yellow for 3 seconds it simply means that it needs to be charged
Lets try the following steps
Step One
·Ensure the Pocket Charger is charged
·Turning ON the Pocket Charger by pressing the button for 4 seconds
·Place the Holder in the Pocket Charger
Step Two
Make sure that the Holder lights on the Pocket Charger pulse to indicate the Holder is charging.
Step Three
Clean the contacts of the Holder and the Pocket Charger.
Step Four
If this does not work, check the Holder using a second, different Pocket Charger or visit an IQOS store to try charging the Holder with a different Pocket Charger.
After following these steps, did you manage to charge the Holder?
Inhalation experience lasting less than it is designed for
A list of possible causes have been listed bellow
Check One
Unlike conventional cigarettes IQOS ILUMA heats tobacco so you have to puff with intervals in order to allow the device time to heat the tobacco and generate the required aerosol.
Check Two
Ensure the device was used in the working temperature range 0-40°C.
Notes
TEREA sticks are designed to deliver 14 puffs or six minutes experience (whichever comes first)
TEREA sticks may or may not leave a stain once they have been used. No stain mark is not a sign the tobacco was not heated properly.
IQOS ILUMA is designed to be used only with TEREA sticks. Do not use IQOS ILUMA and TEREA sticks with previous IQOS generations, as this may cause damage to your device. Do not ingest or disassemble TEREA™ sticks. This product contains a sharp metal part which can cause serious injury if swallowed. Keep out of reach of children More information on www IQOS com
Inhalation experience lasting less than it is designed for
Check Five
Check the TEREA stick was not accidentally used twice. Or that it was just a case with an individual TEREA stick. Isolated cases with a single TEREA stick do not justify blaming the device or the sticks
Check Six
Ensure the TEREA stick was inserted correctly as per the user guide instructions.
Check Seven
TEREA packs should not be stored in an environment which is too humid or too dry. Doing so can have an effect on the aerosol quality.
Note: Keep in mind that used TEREA sticks tend to have visible creases and marks once used, check to see if the stick may have accidentally been already used.
Cosmetic damage (such as scratches, dents, broken plastic, hairline cracks, discoloration), damage (improper handling or liquid contact) or failure caused by normal wear and tear of your device are excluded from voluntary warranty program.
Our online store offers a wide range of accessories designed for IQOS ILUMA that could help you minimize the impact of the cosmetic damage.
If you wish to speak to a Customer Care representative, please contact us at:
800MYIQOS (694767)
This product is not risk free and provides nicotine, which is addictive. Only for use by adults.
Ensure it was not used out of the working temperature 0-40°C.
Step Two
Check if the led blinks white 8 times this indicates that the device cannot deliver a second experience.
Step Three
Check the Pocket Charger is charged and is able to charge the Holder. In the even the contacts are dirty this can have an effect on charging (click here to see how to clean)
Note: a used TEREA stick can be used to perform this test
After following these steps does the Holder remain ON for six minutes during the second experience?
•Turning ON the Pocket Charger by pressing the button for 4 seconds
•Place the Holder in the Pocket Charger
Check TWO
Ensure the Autostart function hasn’t been de activated in the IQOSApps
Check THREE
IQOS ILUMA is designed to be used only with TEREA sticks. The device will not start with any other sticks
Check FOUR
Ensure the TEREA sticks are being placed in the holder in the right direction and the line being aligned with the top of the Holder
IQOS ILUMA is designed to be used only with TEREA sticks. Do not use IQOS ILUMA and TEREA sticks with previous IQOS generations, as this may cause damage to your device. Do not ingest or disassemble TEREA™ sticks. This product contains a sharp metal part which can cause serious injury if swallowed. Keep out of reach of children. More information on www IQOS com
Try a second TEREA stick to see if the issue repeats itself.
IQOS ILUMA is designed to be used only with TEREA sticks. Do not use IQOS ILUMA and TEREA sticks with previous IQOS generations, as this may cause damage to your device. Do not ingest or disassemble TEREA™ sticks. This product contains a sharp metal part which can cause serious injury if swallowed. Keep out of reach of children. More information on www.IQOS.com
Place the Holder in the Pocket Charger and perform a RESET by pressing and holding down the Pocket Charger button for 10 seconds (until the lights fade out). The RESET is confirmed when you release the button and all Lights blink three times.
Step Two
Try to insert a stick.
IQOS ILUMA is designed to be used only with TEREA sticks. Do not use IQOS ILUMA and TEREA sticks with previous IQOS generations, as this may cause damage to your device. Do not ingest or disassemble TEREA™ sticks. This product contains a sharp metal part which can cause serious injury if swallowed. Keep out of reach of children. More information on www.IQOS.com
If issue continues, you may need to upgrade the firmware on your IQOS ILUMA device. Please download the firmware and upgrade your IQOS ILUMA PRIME device:
Alternatively, you may visit an IQOS Store with your IQOS ILUMA device to get the firmware on your device upgraded.
Step THREE
After the firmware upgrade is completed, fully charge the holder, both LEDs must light up with a short button press
Step FOUR
Insert a TEREA stick
IQOS ILUMA is designed to be used only with TEREA sticks. Do not use IQOS ILUMA and TEREA sticks with previous IQOS generations, as this may cause damage to your device. Do not ingest or disassemble TEREA™ sticks. This product contains a sharp metal part which can cause serious injury if swallowed. Keep out of reach of children. More information on www.IQOS.com
After a TEREA stick is properly inserted in the holder, try to start an experience by pressing the button for 2 seconds.
IQOS ILUMA is designed to be used only with TEREA sticks . Do not use IQOS ILUMA and TEREA sticks with previous IQOS generations, as this may cause damage to your device. Do not ingest or disassemble TEREA™ sticks. This product contains a sharp metal part which can cause serious injury if swallowed. Keep out of reach of children. More information onwww.IQOS.com
Cosmetic damage (such as scratches, dents, broken plastic, hairline cracks, discoloration), damage (improper handling or liquid contact) or failure caused by normal wear and tear of your device are excluded from voluntary warranty program.
Our online store offers a wide range of accessories designed for IQOS ILUMA that could help you minimize the impact of the cosmetic damage.
If you wish to speak to a Customer Care representative, please contact us at:
800MYIQOS (694767)
This product is not risk free and provides nicotine, which is addictive. Only for use by adults.
This may be due to segments of a previous TEREA stick remaining in the Holder.
Let’s try the following:
Step One
With caution, use your two fingers to remove the TEREA stick, if this does not work.
Step Two
With caution, try using a toothpick to remove the part of the stick that remains in the device. When removed, dispose of it immediately. Do not use any sharp tools to remove the broken stick as you might damage the device.
IQOS ILUMA is designed to be used only with TEREA sticks. Do not use IQOS ILUMA and TEREA sticks with previous IQOS generations, as this may cause damage to your device. Do not ingest or disassemble TEREA™ sticks. This product contains a sharp metal part which can cause serious injury if swallowed. Keep out of reach of children. More information on www.IQOS.com
If you are experiencing any trouble please go to your nearest IQOS store so that one of our agents can assist you.
This may be due to segments of a previous TEREA stick remaining in the Holder. Let’s try the following:
Step One
With caution, use your two fingers to remove the TEREA stick, if this does not work.
Step Two
With caution, try using a toothpick to remove the part of the stick that remains in the device. When removed, dispose of it immediately. Do not use any sharp tools to remove the broken stick as you might damage the device.
If you are experiencing any trouble please go to your nearest IQOS store so that one of our agents can assist you.
IQOS ILUMA is designed to be used only with TEREA sticks. Do not use IQOS ILUMA and TEREA sticks with previous IQOS generations, as this may cause damage to your device. Do not ingest or disassemble TEREA™ sticks. This product contains a sharp metal part which can cause serious injury if swallowed. Keep out of reach of children. More information on www.IQOS.com
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Do you want to proceed to eligibility check?
Click “Start” and login, select or add the correct device, and proceed with diagnostics.
Let‘s identify the right device part that is causing the issue
Let’s identify the correct device part that is causing the issue.
1. Place the holder inside the pocket charger. Ensure to place it correctly.
2. Briefly press and release the pocket charger button and observe what you are seeing from the below:
Option A: No lights turning ON. This means your pocket charger may have an issue.
Option B: The pocket charger (strip lights) are briefly turning ON, the holder status (rounded lights) are OFF. This means your pocket charger is working, but holder is still not.
After these steps, please choose the suitable option from below
Please enter your date of birth to confirm you are an adult [18+] smoker or user of nicotine products.
Are you an adult (18+) smoker or user of any other nicotine products?
You must be 18 or over to access materials on this site.
We care
This website contains information about smoke-free products and we need your age to make sure that you are an adult in the United Arab Emirates who would otherwise continue to smoke or use tobacco products. PMI’s smoke-free products are not an alternative to quitting and are not designed as cessation aids. They are not risk free. They provide nicotine, which is addictive. Only for use by adults. Please visit Important Information page of this website for further risk information.
Country redirect
Please note this site is intended for United Arab Emirates. In order to ensure compliance with local legal requirement, we need to redirect you to your country of origin.
